progress pic's

[TPI383]

Don't mind the messy garage. It deff. needs a good spring cleaning.

anyways.......

Mocking up parts Ive been collecting.

Need to do a little Inner fender well cutting in the rear now.
4linked 9inch,31 spline axles ,coil overs., 4piston willwood brakes.
http://www.cecoatings.com/images/CarStuff/new%20project%20car/9inchrearend/DSC03643.JPG
http://www.cecoatings.com/images/CarStuff/new%20project%20car/9inchrearend/DSC03649.JPG
http://www.cecoatings.com/images/CarStuff/new%20project%20car/9inchrearend/DSC03646.JPG

15x10 with slicks. and 15x3 up front. (for the track) I still have my 17x9.5 with 275/45/17 for the street
http://www.cecoatings.com/images/CarStuff/new%20project%20car/DSC03644.JPG

Cage and 4thgen seats. Dash will go in after I pull it all out and paint the cage now that its not cold out.
http://www.cecoatings.com/images/CarStuff/new%20project%20car/Cage/RearBars.jpg
http://www.cecoatings.com/images/CarStuff/new%20project%20car/Cage/side.jpg

Motor
SBC Little old turbo good for around 900wrhp I only plan to run 12-18psi on the street.
Vic jr I converted to EFI. will be using a 90* elbow and a LS1 style throttle body
http://www.cecoatings.com/images/CarStuff/new%20project%20car/Turbomockup/Turbo1.jpg

need a tranny next. Don't what I wanta run.

So who else is finally workin on something? HOPEFULLY i'll have it out before snow fall....lol.

[87IROC Z]

Looks good. Im a couple days of work away from getting the rest of what i need off the z.

[TPI383]

sweet. Let me know when you want my doors/etc.. Spring is here time to clean out my mess of a garage. :)

[87IROC Z]

will do. im ready whenever you want though. ive got room so as soon as you want to clean house let me know.

[survival]

You still going with the 406 or did you decide on something else? Nine inch looks nice,did you put the gusseting on did you get it like that nice race setup though.

I'll putting the 3.70s in real soon,been to busy with getting house electrical 220v in the garage now.

[TPI383]

355 for now. untill I get the tuning down for the boost.
Then I'll put the real motor in. Bowtie blocked 4.170 bore motor :) Roller Cam bearings, Solid roller Cam. etc..

Id rather not destroy a Good motor on learing the tuning curve on a big boost motor.

picked rear end up like that. Im welding on some LCA brackets also. so It can be used as a 4link setup for lca's

[chainsaw]

lol, your garage looks better than the last time i saw the inside of it, heheh

[Mkos1980]

My car starts off in 4th gear then shifts to 3rd, then to second and wont go into 1st then because I am going too fast. Jamy and I swaped in the new 4L60E in the Formy and tried to use the 411 ECM to control it but the shifting is reversed. Instead of 1, 2, 3, 4 its 4, 3 , 2 , 1 LOL First time driving I was like HOLY SHIT this new converter is loose but I was starting off in 4th lol. Few minor bugs lol

Anybody got a shifter cable? I broke mine lowering the tranny done. Snapped it somewhere.

[87IROC Z]

ahhh, two days too late. I just got rid of the remainder of the shell i had. It still had a working cable.

[Mkos1980]

Dealer wants 80 bucks :(

[TPI383]

Dealer wants 80 bucks :(

I might have a extra one. $80 is crazy.

[Mkos1980]

I take that back. I called Spitzer and its 64.50 for one. Thats still nuts considering You can prob get them for like 15 bucks at a boneyard. This snow is not helping :( I would go look but not now! lol

TPI Let me know asap on the status of a cable. My car is face forwar din the garage with it still in D lol

[TPI383]

I can pull the one outa my car if you need one ASAP man. I can replace mine later. No big deal.

[TPI383]

Matt,

You still need that cable?

[Mkos1980]

Chris, I found a hookup at the local buick dealer and got it for cost. about 30 bucks brand new. Thanks anyways!